ELECTRIC TRIM TAB KITS 12
lencomarine.com
Standard Performance Trim Tab Kits 12V System Our first series designed specifically for performance. This system comes equipped with a thicker reinforced hinge and complimented with an Electro-Polished finish for added quality and protection. Boat lengths 13' (4 m) to 40' (12.2 m)
Heavy Duty (HD) Performance Trim Tab Kits 12V System The Heavy Duty series is designed & built for the boats that need extra strength to support them in rougher water at higher speeds. Boat lengths 18' (5.5 m) to 42' (12.8 m)
15037-101 Electro-Polished
15043-101 Electro-Polished
Blades are constructed of Electro-Polished 12-gauge (2.7 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 1/4" (6.4 mm) diameter hinge pin.
Blades are constructed of Electro-Polished 12-gauge (2.7 mm) laser cut 304 stainless steel with 1" (2.5 cm) turned up edges and a 5 degree taper on the inside, heavy duty hinge with 1/4" (6.4 mm) diameter hinge pin. Full transom back plate with welded on stainless steel upper & adjustable lower actuator mounting brackets, 5/16" (.8 cm) stainless steel mounting bolts & mechanical strain-relief cable seals. 3.75" (9.5 cm) sacrificial anodes installed. Kits include: • (2) 12-gauge stainless steel Electro-Polished blades • (2) 15055-001 XD Extreme Duty actuators with 6' (1.8 m) leads & Deutsch connectors • (2) 30133-103 actuator extension wiring harnesses - 20' (6.1 m) length
Kits include: • (2) 12-gauge stainless steel Electro-Polished blades • (2) 15054-001 actuators with 6' (1.8 m) leads & Deutsch connectors • (2) 30133-103 actuator extension wiring harnesses - 20' (6.1 m) length • (2) 15085-001 upper mounting brackets with gland seal • (2) 50014-001 lower mounting brackets
= Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below.
• Lenco owner's/installation manual • Note: Boat-mounting hardware to be supplied by the customer
= Width of hinge = Length of tab SIZE DESCRIPTION Size description to be used with chart below.
• Lenco owner's/installation manual • Stainless steel mounting hardware
SHIPPED FULLY ASSEMBLED
Hinge Height
Min. Transom Height 13.5" (34.3 cm) 13.5" (34.3 cm) 11" (27.9 cm) 11" (27.9 cm) 11" (27.9 cm) 11" (27.9 cm) 11" (27.9 cm)
Part #
L" X W" 9" x 9" 9" x 12" 12" x 9"
Boat Length
15034-101 15035-101 15036-101 15037-101 15038-101 15039-101 15040-101
13'–20' 16'–26' 16'–26'
2" (5.1 cm) 2" (5.1 cm) 2" (5.1 cm) 2" (5.1 cm) 2" (5.1 cm) 2" (5.1 cm) 2" (5.1 cm)
Back Plate Dimensions
12" x 12" 18'–32' 14" x 12" 19'–34' 16" x 12" 20'–36' 18" x 14" 22'–40'
6" (15.2 cm)
5" (12.7 cm)
15044-101
15041-101 15042-101 15043-101
8" (20.3 cm) 2"
8" (20.3 cm)
10" (25.4 cm)
10" (25.4 cm)
2" (5.1 cm)
(5.1 cm)
12" (30.5 cm)
14" (35.6 cm)
Switch kits sold separately See pages 30–32
The actuator leads pass through the water-tight mechanical strain-relief cable seal and the back plate before passing through the transom. This applies to all products with back plates.
Part #
L" X W"
Boat Length Min. Transom Height
15041-101 15042-101 15043-101 15044-101
12" x 12" 14" x 12" 16" x 12" 18" x 14"
18'–34' 19'–36' 20'–38' 22'–42'
10.5" (26.7 cm) 10.5" (26.7 cm) 10.5" (26.7 cm) 10.5" (26.7 cm)
Switch kits sold separately See pages 30–32
Powered by FlippingBook