100 SERIES ACTUATORS & HATCH LIFTS
53
lencomarine.navico.com
Optional Hatch Lift Accessories
12 Volt Models
Approximate L.O.A. Retracted 15" (38.1 cm)
Approximate L.O.A. Extended 19" (48.3 cm)
Approximate Stroke 4" (10.1 cm) 6" (15.2 cm) 8" (20.3 cm) 8" (20.3 cm) 12" (30.5 cm) 12" (30.5 cm) 16" (40.6 cm) 16" (40.6 cm) 20" (50.8 cm) 20" (50.8 cm) 24" (60.9 cm) 24" (60.9 cm) 26" (66.0 cm) 30" (76.2 cm)
Superseded Part #
Part #
20760-001 20762-001 20764-001 20766-001 20768-001 20770-001 20774-001 20776-001 20778-001 20780-001 20782-001 20784-001 20786-001 20788-001
HL-400 HL-600 HL-800S HL-800 HL-1200S HL-1200 HL-1600S HL-1600 HL-2000S HL-2000 HL-2400S HL-2400 HL-2600 HL-3000
20" (50.8 cm) 26" (66.0 cm) 20" (50.8 cm) 28" (71.1 cm) 24" (60.9 cm) 32" (81.2 cm) 24" (60.9 cm) 36" (91.4 cm) 29" (73.7 cm) 41" (104 cm) 29" (73.7 cm) 45" (114 cm) 33" (83.8 cm) 49" (124 cm) 33" (83.8 cm) 53" (134 cm) 37" (93.9 cm) 57" (144 cm) 37" (93.9 cm) 61" (154 cm)
Hatch Lift Rocker Switches 12 & 24 Volt Rocker Switch for hatch lifts with two 30" non-terminated power leads.
This switch is CE certified and ABYC compliant. It is also 20A rated and clam shell packaged.
15096-001 15098-001
Single Hatch Lift Dual Hatch Lift
41" (104 cm) 47" (119 cm) 47" (119 cm)
65" (165 cm) 73" (185 cm) 77" (195 cm)
24 Volt Models
Stainless Steel Non-locking Slide Bracket For hatch lifts. In case of power failure, this bracket allows you to pull the hatch open a minimum of 5" (12.7 cm) in order to remove bolt for access. Non-retail box. 70381-001
Approximate L.O.A. Retracted 15" (38.1 cm)
Approximate L.O.A. Extended 19" (48.3 cm)
Approximate Stroke 4" (10.1 cm) 6" (15.2 cm) 8" (20.3 cm) 8" (20.3 cm) 12" (30.5 cm) 12" (30.5 cm) 16" (40.6 cm) 16" (40.6 cm) 20" (50.8 cm) 20" (50.8 cm) 24" (60.9 cm) 24" (60.9 cm) 26" (66.0 cm) 30" (76.2 cm)
Superseded Part # HL-400/24V HL-600/24V HL-800S/24V HL-800/24V
Part #
20761-001 20763-001 20765-001 20767-001
6.25" (15.9 cm)
20" (50.8 cm) 26" (66.0 cm) 20" (50.8 cm) 28" (71.1 cm) 24" (60.9 cm) 32" (81.2 cm) 24" (60.9 cm) 36" (91.4 cm) 29" (73.7 cm) 41" (104 cm) 29" (73.7 cm) 45" (114 cm) 33" (83.8 cm) 49" (124 cm) 33" (83.8 cm) 53" (134 cm) 37" (93.9 cm) 57" (144 cm) 37" (93.9 cm) 61" (154 cm)
HL-1200S/24V 20769-001
20771-001
HL-1200/24V
HL-1600S/24V 20775-001
20777-001
HL-1600/24V
HL-2000S/24V 20779-001
Stainless Steel Pull Pin Clamshell packaged. 60101-001D
20781-001
HL-2000/24V
HL-2400S/24V 20783-001
20785-001 20787-001 20789-001
41" (104 cm) 47" (119 cm) 47" (119 cm)
65" (165 cm) 73" (185 cm) 77" (195 cm)
HL-2400/24V HL-2600/24V HL-3000/24V
Lenco Hatch Lift Mounting 1. Follow the chart to the right to figure out load on the hatch lift. Maximum load is 500 lbs (226.8 kg). Y = Total length of hatch X = Length from the hinge to the hatch lift mounting point W = Weight of the hatch to be lifted 2. Determine the angle of the hatch lift mount. Do not exceed 45 degrees from center. 3. Mount the hatch lift on the desired location as per the above instructions. Important: It may be necessary to shim the upper or lower mounting bracket up or down so the hatch does not bind when fully closed. The hatch lift does not stop pulling until it has reached its fully closed position. If the hatch fully closes before the hatch lift is fully retracted, it will cause damage to the lift or the mounting hardware. Shim the hatch lift with stainless washers for small amounts of length. Use Lenco shim part #50015-002D for lengths greater than 1/8" (3.2 mm). 4. Wire to switch according to the hatch lift wiring diagram in manual.
W LBS/KG
Y Length IN/CM
X Length IN/CM
45 MAX
45 MAX
Hatchlift
YxW÷X=Force
Powered by FlippingBook